What is a Maxitrol regulator used for? Maxitrol’s 325‑L Series line pressure regulators with OPDs are for use on piping systems up to 5 psi. The regulator reduces pounds pressure to a level within the
What is a Maxitrol regulator used for?
Maxitrol’s 325‑L Series line pressure regulators with OPDs are for use on piping systems up to 5 psi. The regulator reduces pounds pressure to a level within the appliance or equipment’s operating supply range. The line regulator is located upstream of equipment already fitted with an appliance regulator.
What pressure should propane regulator?
Unlike, natural gas appliances that operate at pressures around 7 inches of water column (WC) or 14.9 millibars, 1743 Pa, or about 0.25 psi (pounds per square inch, a common operating pressure range for propane (liquid petroleum or LP gas) appliances is 10 – 11 inches WC or 27.4 millibars, 2491 – 2739 Pa or about 0.36 …
Are all propane regulators the same pressure?
Every propane gas grill uses an LP regulator, but not all regulators are created equal. Though the purpose is the same, different types of setups require different types of regulators. The type of regulator a grill needs is based on the specific propane application requirements.
Do gas regulators need to be vented?
The natural gas regulator is a critical component of the meter set and needs to be vented and should comply with local and federal venting requirements (may vary from county to county). The vent functions as a safety measure and allows the diaphragm within the regulator to breathe.
What is the difference between a high pressure and low pressure propane regulator?
Low-pressure propane burners regulate gas intake to about 6 ounces per square inch, whereas high-pressure burners regulate gas intake to between 1 and 60 pounds per square inch. The intake difference determines the burners’ application: outdoor or indoor.
What’s the difference between a low pressure regulator and a high pressure regulator?
A residential application will require a low pressure regulator which reduces the gas pressure to 6 ounces (10.5 inches water column). High pressure regulators regulate the output pressure from 1 psi to as high as 60 psi.
How do you know if a gas regulator is bad?
These faulty gas regulator symptoms will let you know that it’s time to get a new one.
- Yellow Flames:
- Sooty Residue:
- Popping Sounds:
- No Propane Flow:
- Faulty Vents and Leaking:
- Automatic Changeover is Malfunctioning:
- It’s Been Frozen:
- It’s Been Dunked in Water:
What kind of pressure regulator does Maxitrol use?
Maxitrol’s 325‑L Series line pressure regulators are for 2 psi piping systems. 325 series regulators are used for residential, commercial, and industrial applications. The 325 series features a high leverage linkage assembly to deliver positive dead-end lockup.
What kind of pressure regulators are used for 2 psi?
325‑L Series Line Pressure Regulators — 2 psi Maxitrol’s 325‑L Series line pressure regulators are for 2 psi piping systems. 325 series regulators are used for residential, commercial, and industrial applications. The 325 series features a high leverage linkage assembly to deliver positive dead-end lockup.
What’s the inlet pressure on a Maxitrol rv48l?
MARKING – Model: RV48L, Marking: 1/2 PSIG, Po 5″ – 12″. Inlet pressure 1/2 PSI. Adjustable outlet pressure 5″-12″ Water Column. OPERATE TEMPERATURE – 32°F – 225°F (0°C – 107°C). Do not install the regulator too close to the heating equipment or use in very cold environment. Heat or cold can change the resistance of the spring inside the regulator.
What is the maximum inlet pressure for LP / propane?
1 CF of LP/propane = 2500 BTU Minimum Inlet Pressure as measured at the regulator Max. Capacity