How do I fix a fuser error on my HP printer?

How do I fix a fuser error on my HP printer?

Solution one: Reset the printer

1. Press the Power button to turn off the printer.
2. Disconnect the power cord from the rear of the printer.
3. Wait 30 seconds, and then reconnect the power cord.
4. Press the Power button to turn on the printer. Wait for the product to start.
5. Try printing again.

How do I reset my HP LaserJet p3005?

Perform a cold reset:

1. Turn the device off.
2. Turn the device on. When the memory count begins, press and hold the check button.
3. After the message SELECT LANGUAGE appears on the display, press the arrow up or arrow down buttons until COLD RESET is highlighted.
4. Press the check button.

How do you fix a 50.9 fuser error?

Yes, it is commonly a Fuser related issue.

1. Verify the fuser is installed correctly and fully seated.
2. Turn off the printer, remove and reseat the fuser.
3. if same issue, replace the Fuser unit.
4. If no go, then need to replace the DC controller PCA.

How do I fix my HP 50.2 fuser error?

For a temporary fix, you can try turning your printer off and back on again. Sometimes the reboot will allow the fuser to reset itself and you can print a few more pages. If the 50.2 Slow Fuser error message returns, it’s time to replace your fuser.

How do I fix a 50.7 fuser error?

How To Fix Hp Printer Fuser Error 50.7

1. Restart the printer. Sometimes, there is a small fault with the printer flag reader.
2. Plug directly into the wall.
3. Reinstall the fuser.
4. Fuser pressure-release sensor flag.
5. Fuser pressure-release drive test.
6. Replace the fuser.

What does 50.2 fuser error mean?

Slow Fuser
The 50.2 fuser error message is a “Slow Fuser” error, which is a time-out error where the fuser is not warming up fast enough. If the 50.2 Slow Fuser error message returns, it’s time to replace your fuser.

What is a fuser on a printer?

A fuser unit is a pair of heated rollers within the printer that fuses the toner onto the paper being printed on. Toner particles are pulled to the paper to create the desired text and images as the paper passes the imaging drum. After the paper is passed through the fuser assembly, it is rolled out to the output tray.

What does 50.7 fuser error mean?

fuser failure
If you have NOT recently replaced the fuser or heavily jostled the printer around, then the 50.7 Fuser error indicates you have an actual fuser failure (the gearing pressure is not releasing) and the fuser needs replacing.

How do you know when a fuser is bad?

Streaking, smudging, black lines, and double images are all symptoms of a bad fuser. When you notice these printing defects and experience problems, such as paper jams or wrinkles, this is a good sign to replace the fuser kit.

How to fix a 50.7 fuser error message?

Plug the product directly into the wall socket. Turn the product power on. If you still receive the message follow the steps below. 1. Turn the product power off, wait at least 30 seconds, and then turn the product power on and wait for it to initialize. If you still have the messages continue with next step.

Why does paper stick to HP LaserJet P3005?

The paper hits that and blocks on optical sensor below that signals it is exiting the fuser. If it doesn’t hit that sensor at the proper time, it will give the .05 error. There is a plastic sleeve that slides around the heater assy. If that sleeve isn’t properly lubricated then the paper will stick because the sleeve will act as a brake.

Why does my printer say 13.05 on my HP printer?

13.20, probably triggered by the sensor flag in the fuser itself. 13.05, probably triggered by paper moving through the printer when the fuser gets jammed. when you fix the fuser jam, you should fix 13.05 automatically. best of luck… Thanks for the responses.