How do you calculate winch drum capacity? drum capacity in feet = (A + D) x A x B x K K = factor from the table A = (H – D – 2Y) ÷
How do you calculate winch drum capacity?
drum capacity in feet = (A + D) x A x B x K K = factor from the table A = (H – D – 2Y) ÷ 2 Y = clear distance between edge of flange and wire rope (usually 1/2″). In some applications a two part line can be used to effectively increase the size of load the winch can move.
How are winches loads calculated?
You must determine how fast (the speed of the line or line speed) that the load will be pulled (feet or meters per minute). You can do so by taking the distance that you need to move the load and dividing by the speed of the winch. As an example: 100 feet divided by 10 feet per minute = 10 minutes.
What size is winch cable?
5/16″ steel cable is rated at 9,800lbs which is just above the maximum pull strength of the winch. 5/16″ synthetic winch rope is around 12,000lbs breaking strength. But, the most common size used on winches ranging from 8k to 12k is 3/8″ diameter for the reasons mentioned above.
How do you calculate drum capacity?
Multiply the radius squared times pi times the height of the drum. Pi is approximately 3.14159265. The final result is the volume of the drum in cubic units, the same units you used to make the measurements.
How do you measure drum length?
Length is calculated to the top of the drum flange minus selected freeboard (i.e. clearance) . If “Full drum” is selected under Freeboard options then the length is calculated to the top of the flange without any freeboard, The (3) dead (anchoring) wraps are included in all outputs.
How strong is a 2500 lb winch?
A trailer winch that is 2,500 can pull ten percent of the slope, which is 12,563lbs, and a hundred percent of the hill of 3,213lbs.
How do you calculate winch size?
Winch sizes Your winch should be able to pull at least 1.5 times the weight of your vehicle. You can calculate it by taking the gross vehicle weight and multiply it by 1.5. This is the minimum rating, but certain factors can make your winch capacity be exceeded.
How do I choose a winch size?
A common rule of thumb is to simply double the weight of your vehicle. Midsize pickups like a Toyota Tacoma or Nissan Frontier can use a 9,000- to 9,500-pound-capacity winch. Full-size trucks like a Ford F-150 or Chevy 1500 require at least a 12,000- or 12,500-pound-capacity winch.
What are the dimensions of a Maytag front load washer and dryer?
Measurements shown below are examples based on Maytag ® front load washer and dryer models MHW8630H & MED8630H. Decide which washer and dryer setup will work best for your space.
How to calculate the drum capacity of a winch?
Drum Capacity in Feet = (A + B) * A * C * K Factor.
What are the specs of a Maytag refrigerator?
1 1-82180-002 – Upright Freezer 2 100646G – Commercial Washer 3 11-06-00 – Microwave Oven 4 110 – Range 5 110651-3 – Top Mount Refrigerator 6 110898-2 – Side By Side Refrigerator 7 111208-1 – Refrigerator 8 111244-1 – Top Mount Refrigerator 9 111273-1 – Side By Side Refrigerator 10 111406-1 – Side By Side Refrigerator
What happens when wire is wrapped around a winch?
When wire is wrapped around that cylinder in many layers (full drum) the winch will operate at higher line speed and lower line pull. When the winch is at bare drum (no wire on the drum) the winch will operate at slower line speed and higher line pull.